What's new
Cooking Forum

This is a sample guest message. Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

Roast Beef?

M

mitchb2

Guest
Hello...new here.

I make a good pot roast, and I'm slowly learning about the different cuts of beef.

I'd like to make a roast beef that's cooked to medium and sliced, as opposed to pot roast that's cooked for a long time at low temperature.

Do I have to use an expensive cut, such as prime rib or tenderloin?
 
Several cuts are well suited to oven roasting. The most elegant choice is a tenderloin roast, which is lean and tender, but very expensive. A rib roast (sometimes called a prime rib roast) isn't as lean and tender, but it's juicier and more flavorful. A good compromise between the two would be a rib-eye roast, which is basically a boneless, low-fat rib roast. Other candidates for roast beef are a top loin roast, top sirloin butt roast, tri-tip roast, round tip roast, and rump roast. Don't assume that anything with "roast" in its name will work as roast beef. Some roasts are intended for pot roast recipes, for it takes hours of cooking in a liquid to make them tender enough for civilized consumption.

Steps for Producing a Simple Roast Beef

The following roasting method works best for beef cuts that weigh about 2½ pounds. Adjustments in the roasting time will have to be made if using a smaller or larger piece of meat. A top sirloin butt roast, a tri-tip roast, or a top quality bottom round roast are good choices when using the following steps.

Preheat the oven to 450°F. Remove the beef roast from the refrigerator and season the meat as desired. The meat may also be marinated for several hours before it is roasted. This may be especially desirable if roasting a bottom round, because even a top quality bottom round roast will not be as tender as the top sirloin butt or tri-tip roast.

Place the beef on a rack in a shallow roasting pan with the fat side up. Do not cover the roast or add any liquid (liquid is used for braising and not roasting).

Allow the beef to roast at 450°F for 45 minutes and then begin checking the internal temperature of the meat with a meat thermometer. Continue roasting the meat until the internal temperature has reached 5 or 10 degrees below the desired doneness. Cooking a small roast at high heat helps to sear the exterior, which provides a flavorful browned crust and and tender meat.

The total roasting time depends on the type of beef cut that is roasted, the weight of the beef cut, the level of doneness desired, and the accuracy of the oven. Generally, the total roasting time may range from 15 to 30 minutes per pound. The 2½ pound, bottom round roast pictured at the right, required 55 minutes cooking time to reach the desired doneness (medium/medium rare).

Remove the roast from the oven and place aluminum foil loosely over the meat to hold in the heat. Let the roast stand for 15 minutes. The temperature will continue to rise 5 or 10 degrees, reaching the proper doneness. The resting period will allow the juices to settle in the roast making it more tender and easier to carve.

A beef roast cooked to medium rare should have an internal temperature of 145°F - 150ºF after the resting period and a roast cooked to medium should have an internal temperature of 150°F to 165ºF. (See the note below).


Note: Traditional guidelines state that beef cooked very rare, rare, or medium rare should have an internal temperature ranging between 115ºF to 140°F. With increased concern over bacteria that may be present in the internal portions of beef , it is now recommended that whole beef cuts be cooked to an internal temperature of not less than 145°F.
 
Thanks for the great reply.
If all I can find is bottom round, can you recommend a marinade?
 
here's a few that I have -

1/4 cup olive oil
2 tbsp Soy sauce
1/4 cup bourbon, dry sherry or dry red wine
1 tsp garlic powder
Freshly ground black pepper

Combine all ingredients and pour over meat. Marinate in refrigerator. May also be used as a mop sauce during cooking process. This sauce is good on red meat, fish and chicken.



2 cans beer
2 tsp salt
1/2 cup olive oil
1 tsp cayenne pepper
1 tbsp wine vinegar
1 tbsp prepared horseradish
1 tsp onion powder
2 tbsp lemon juice
1 tsp garlic powder

Mix all ingredients together and use as a marinade. Also use as a mop sauce during slow cooking. Please use a full-flavored beer.



I have used bottom round many times - I usually just drizzle with oil and "roll" in the roasting pan to coat with the oil, season with fresh garlic, kosher salt, black pepper and fresh parsley; cover; roast at 350* F. and I have always had a very tender roast.
 
I'm confused now. :)
The first post says 450 degrees, uncovered.
The second one says 350 degrees, covered.

By the way, I bought a 3.5 pound rump roast.
 
Last edited:
it's your choice - I stick to the 350* F because I like mine more well done - many swear that the 450 gives them a better "rare" or medium rare
 
Came out perfect. Thanks!
I'll definitely make this again.
 
question on temperature?

If you are baking a roast and you test the temperature, and it is not there yet. How long do you wait to test it again. Is there a scale to how many minutes to how many degrees go by? I can't bake a good roast yet and each time I make it the temperature goes over. I don't know how soon to check it again.
 
Probably your best bet is to get one of those electronic thermometers that you can plug into the meat, and set the display outside of the oven. They usually come with a temperature alarm that will go off at the desired temperature. I bought one at the grocery store a couple years ago and works great when your slow cooking meat.
 
interesting

I didn't know there was such a thing, Thanks! It often bothers me to keep checking on the temperature because you have to open the oven door and heat escapes.
 
Lizgirl, see my comments in your pork roast thread about hold-over cooking. That's certainly part of your problem.

Jafo is certainly right about the remote probe type thermometers. I've found the best one, balancing price and reliability, is available from the King Arthur Flour people. Check their website for details.

To answer your question, there are two many variables for such a chart to exist: the thickness of the meat, the temperature you're cooking it, the relative amount of fat, how quickly your oven cycles.

I know you're frustrated right now. But just take things easy. Soon enough you'll develop a feel for cookery, and will be laughing at the mistakes you make now.

No, not mistakes! Learning experiences.
 
Thank you for your encouragement. I will keep working at this, and looking for one of those thermometers!
 
Back
Top